Prevent iPad overheating issues in the airplane this summer

Your iPad will display this message and stop functioning if the internal temperature gets too warm.

Your iPad will display this message and stop functioning if the internal temperature gets too warm.

Based on iPad Pilot News reader surveys over the years, the majority of pilots have had the iPad shut down on them at least once in flight due to overheating. This is by far the most common problem reported by pilots when flying with an iPad, but it can be prevented with a little bit of planning and preparation.

Apple lists the normal temperature operating range for the iPad as 32° – 95° F. The recommended temperature for storing your iPad is -4° – 113° F. While there are reports of the iPad shutting down when operating in environments well below freezing, the most likely result will be lagging as you interact with the touchscreen (tip – when operating in cold environments, plug it into a charger and use a case to help generate and retain heat).

The more likely scenario when operating at the extreme ends of the temperature operating range is overheating, which will lead to the iPad entering a thermal protection mode where it will become completely unusable until the internal temperature of the device is reduced. The primary reason for this is to protect the enclosed lithium-polymer battery (bad things can happen if they get too hot).

There are a couple of ways on a typical flight that this can happen and both will catch you off guard if you’re not paying attention. The first scenario can happen when you’re flying in a low-wing airplane en route at altitude with the iPad secured in a kneeboard on your lap. You’re in VFR conditions in sunny weather, but the iPad is out of direct sunlight. Then you make a turn over a waypoint, and the sun begins to shine directly on your iPad’s dark screen without you noticing. Even though the ambient temperature may be well below the 95° F limit, the iPad’s internal temperature will quickly elevate and soon display the overheat warning.

Battery pack and iPad

Charging your iPad can exacerbate overheating.

There are several factors that may increase the potential for an overheat situation like this in flight. First, if you’re using the iPad with a fully-enclosed case or kneeboard, you will be restricting airflow around the rear of the iPad, limiting its ability to dissipate heat. Also, charging the iPad from a USB port in the airplane or a backup battery will also increase the internal temperature of the device, increasing the risk for an overheat situation in a hot airplane or near direct sunlight.

The other likely scenario in which your iPad can unexpectedly overheat is after shutting the engine down on the ramp on a hot summer day. Prior to the iPad, many pilots would set their paper charts or kneeboard on the glareshield to get them out of the way. New iPad users might inadvertently do the same thing out of habit. As we all know, the temperature inside the cabin will quickly rise after you shut the door, again putting the iPad in a vulnerable state for potential overheating. Make it a habit to take your iPad with you after shutdown, or store it in a protected part of the airplane to ensure a timely departure when you return.

Your iPad becomes completely unusable when it overheats and will display a temperature warning on the screen. At this point, your only option is to get it to a cooler environment and lower the internal temperature. Remove it from direct sunlight and aim a few air vents over if possible. If you had it in a kneeboard or case, remove these to aid the cooling process, and remove it from any charging sources. Once the iPad’s temperature lowers, it will automatically switch back on—there’s nothing else for you to do at that point, except to keep it out of the sun.

If you fly an airplane that has large windows and lets in a good deal of sunlight to the cabin, your best bet is to consider a yoke or suction cup RAM or Robust mount. These provide plenty of flexibility to pivot the iPad screen away from direct sunlight, and expose more of the front and rear surfaces of the iPad to ambient air for continuous cooling.

If a kneeboard is your only option and overheating is a concern, try raising the iPad slightly above the bottom of the kneeboard to create an open layer of air between it and the backside of the iPad. Many pilots report that adding a few pencils to accomplish this works well. It might be the most polished solution, but it works! For a simpler kneeboard solution that does not restrict airflow, check out the MyClip kneeboard, which does not rely on a traditional rigid base to keep the iPad secure on your lap and allows for more airflow around the device.

You may also want to consider using small sunshades on your windows in flight to help reduce the intensity of the sunlight reaching your iPad. Good options here are the collapsible aircraft sunshades, which attached with suction cups, or slap on sun-visors that cling to the windows on their own.

Another consideration is to use the X-Naut Cooling Case along with your iPad. This mounting system features built-in fans to circulate cool air, specifically targeted at the iPad’s main hot spots to prevent it from overheating. The mount can be powered off of typical alkaline batteries or USB with a power bank or backup battery.

In addition to working with the RAM mount system, you can also turn it into a kneeboard with this accessory kit—perfect for cockpits with a bubble canopy where the iPad is exposed to direct sunlight. The X-Naut is available for the iPad Mini 1-5, the iPad Air 1-2 and 9.7″, the iPad Pro 11″ and Air 4 and the iPad Pro 10.5”/10.2″/iPad Air 2019/iPad (7th Gen).

With a little preparation and some new habits, it’s easy to fly all summer long with an iPad. In fact, after a few early mistakes, we have not suffered an overheating problem in over five years of flying.

15 replies
  1. rob sterling
    rob sterling says:

    Has anyone tried drilling holes in the Ram “E-Z-Roller” plate for ventilation? I want to keep my iPad on charge during flights and this always results in over-heating. It seems like Ram should make this change as the next design goal to improve ventilation.

    • Rob Schmitt
      Rob Schmitt says:

      A pilot on the Beech Talk posted a way of doing this. I copied it and used this for my Ipad Mini. Basically you add a Computer desktop cooling fan to the mount. You have to drill a hole and add a USB type power source. The link at Beehtalk is;

      https://www.beechtalk.com/forums/viewtopic.php?f=34&t=152682

      You do have to create an account to get to this link, but that is no problem.

    • Brad
      Brad says:

      I tried vent holes first and it didn’t seem to help much so I took a dremel and cut out all of the flat plastic and left the webbing. It is still very strong and It allows the back of the iPad to breath better. It helped a lot but being in AZ when it gets to be 115 in the shade I still have issues with the iPad shutting down

  2. rob sterling
    rob sterling says:

    I’m looking for ways to reduce battery drain. If I own and use a Sentry, can I disable both Wi-Fi and cellular – will that reduce the battery drain because the GPS is then disabled?

  3. John Worsley
    John Worsley says:

    I use a kneeboard and have a simple solution. If I’m on a heading keeping the sun on it, I just roll the kneeboard to the side of my leg to get it out of the sun when I’m not actually referring to it. If I’m not paying attention and let it shut off, I unsteady the kneeboard and lay it against the floor vent, which cools it off pretty quickly.

  4. Linda
    Linda says:

    I switched to the RAM X Grip Claw yoke mount attachment and this has helped tremendously in keeping my iPad from overheating. I also try to keep my vents open to allow for as much airflow around the IPad.

  5. ken gross
    ken gross says:

    X-Naut broke after about a month of use—not very sturdy.
    I keep a few sheets of aluminum foil in the plane and on hot sunny days I just place it loosely on the back of my I-Pad to reflect the sun—keeps the I-Pad cooler. Also bring along my old I-Pad on which I keep an up-dated version of Foreflight. If the I-Pad in use gets to overheating I can switch them out and turn off the one I was using to let it cool out of the sun.

  6. Ken Luke
    Ken Luke says:

    I drilled several 3/8 inch holes in the plate of my Ram mount. Have not had the iPad overheat since while in flight. It did overheat when I left it mounted during a fuel and rest stop. Won’t do that again!

Comments are closed.